API St 6AR-2019 pdf free download

API St 6AR-2019 pdf free download.Repair and Remanufacture of Wellhead and Tree Equipment.
1 Scope This standard identifes the requirements for repair and remanufacture of wellhead and tree equipment manufactured in conformance with API Specifcation 6A for continued service when specifed by the user/ purchaser of the equipment. This standard applies to equipment manufactured to editions of API 6A in which a product specifcation level (PSL) identifes the quality, material, and testing requirements for a specifc product. Equipment identifed as manufactured in conformance with API 6A prior to April 1986 (API 6A, 15th Edition) is outside the scope of this document. This standard is not applicable to onsite repair at the equipment installation site. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies, except that new editions may be used on issue and shall become mandatory upon the effective date specifed by the publisher or six months from the date of the revision (where no effective date is specifed). API Specifcation 6A, Specifcation for Wellhead and Tree Equipment API Standard 18LCM, Product Life Cycle Management System Requirements for the Petroleum and Natural Gas Industries, 2017 API Specifcation 20E, Alloy and Carbon Steel Bolting for Use in the Petroleum and Natural Gas Industries API Specifcation 20F, Corrosion-resistant Bolting for Use in the Petroleum and Natural Gas Industries ASME 1 B.18.2.9, Straightness Gage and Gaging for Bolts and Screws ASTM 2 F788, Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series ASTM F812, Standard Specifcation for Surface Discontinuities of Nuts, Inch and Metric Series 3.1.2 date of repair/remanufacture Date of repairer’s/remanufacturer’s fnal acceptance of repaired or remanufactured equipment. 3.1.3 remanufacture Activity where machining, welding, or heat treating have been performed on used or reused parts. 3.1.4 repair Activity where machining, welding, or heat treating have not been performed on used or reused parts. 3.1.5 repairer/remanufacturer Principal agent in the repair and remanufacture of equipment. 3.1.6 replacement part New, repaired, remanufactured, or used part replacing a part in the equipment being repaired or remanufactured. 3.1.7 reused closure bolting Closure bolting from equipment previously in service that is not replaced through the repair or remanufacture process. 3.1.8 reused part Part from equipment previously in service that is not replaced through the repair or remanufacture process. 3.1.9 used part Part taken from an assembly previously in service that is not reused in the same assembly but used in a different assembly. NOTE Used parts include remanufactured parts.
4 General 4.1 Quality Management System The repairer/remanufacturer shall conduct repair/remanufacture operations under a quality management system that conforms to an internationally recognized quality management standard. Where API 6A requirements for quality control are invoked in this document, and API 6A has sampling provisions, sampling shall not be allowed. Each individual part shall be inspected. 4.2? Repair? and? Remanufacture? Specifcation? Levels? (RSL) The repair and remanufacture specifcation level (RSL) shall be designated to provide the appropriate quality control requirements for the repair and remanufacture of wellhead and tree equipment. NOTE 1 PSL is applicable to new product. RSL is applicable to repaired or remanufactured product and may not be representative of the original product PSL or the RSL of the previous repair/remanufacture cycle. NOTE 2 RSL indicates the level of quality control and documentation associated with the repair and remanufacture of equipment and does not represent the technical suitability of equipment for specifc service or performance requirements.