ASME A112.1002-2020 pdf download

ASME A112.1002-2020 pdf download.Anti-siphon fill valves for water closettanks.
A request for interpretation should be clear and unambiguous. The request should • cite the applicable edition of the Standard for which the interpretation is being requested. • phrase the question as a request for an interpretation of a specific requirement suitable for general understanding and use, not as a request for an approval of a proprietary design or situation. The inquirer may also include any plans or drawings, which are necessary to explain the question; however, they should not contain proprietary names or information. ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee. Interpretations are published on the ASME Web site under the Committee Pages at https://cstools.asme.org/ as they are issued. CSA Notes: 1) Use of the singular does not exclude the plural (and vice versa) when the sense allows. 2) Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. 3) This publication was developed by consensus, which is defined by CSA Policy governing standardization — Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be included in the Technical Committee list and yet not be in full agreement with all clauses of this publication.
4) This Standard is subject to review within five years from the date of publication. Suggestions for its improvement will be referred to the appropriate committee. 5) To submit a request for interpretation of this Standard, please send the following information to [email protected] and include “Request for interpretation” in the subject line: a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch; b) provide an explanation of circumstances surrounding the actual field condition; and c) where possible, phrase the request in such a way that a specific “yes” or “no” answer will address the issue. Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are available on the Current Standards Activities page at standardsactivities.csa.ca. 6) Attention is drawn to the possibility that some of the elements of this Standard may be the subject of patent rights. CSA Group is not to be held responsible for identifying any or all such patent rights. Users of this Standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility. ASSE Notes: Notes: 1) Requests for interpretation Requests for interpretation may be sent to any of the (3) standards organizations. All interpretations are reviewed and agreed upon by the ASSE International, ASME, and CSA prior to response. Requests for interpretations may be sent to: Staff Engineering Group ASSE International 18927 Hickory Creek Drive, Suite 220 Mokena, IL 60448-8399
Requests must include: • Name and contact information of the individual requesting the interpretation; • Name of organization the individual represents (if any); • Appropriate references to the standard’s clauses that have a bearing on the issue cited in the request; • A concise explanation of the issue requiring a technical interpretation; • Any supporting documentation that will assist in understanding or describing the issue; • Any recommendations the requestor would like to make concerning a possible technical interpretation, along with appropriate justification or comments. Forms for requests or general guidance can be obtained by emailing [email protected]. 2) Endorsement vs. Listing ASSE International does not endorse any product, but rather lists products that have successfully been applied for and meet the given standard. In exchange the manufacturer is allowed to place the ASSE Seal with the given standard number on their product for public recognition. In order to apply for listing, visit www.asse-plumbing.org/seal/listing_instuctions.html. 3) Patent rights ASSE International complies with Section 3.1 of ANSI Essential Requirements — Inclusion of Patents in American National Standards. To understand what is and is not covered, visit www.ansi.org/ essentialrequirements. 4) Committee or Working Group Membership Each standard is developed by a working group and then approved by the Product Standards Committee and Board of Directors of ASSE International. In order to apply for membership on a working group or any committee, the applications are available at www.asse-plumbing.org/standards/WorkingGroupApp.pdf.