Home>ASME standards>ASME A112.14.6-2010 pdf download

ASME A112.14.6-2010 pdf download

ASME A112.14.6-2010 pdf download.FOG (Fats, Oils, and Greases) Disposal Systems.
1 GENERAL 1.1 Scope This Standard establishes requirements for FOG (fats, oils, and greases) disposal systems. FOG disposal systems shall be designed to (a) remove FOG from effluent (b) retain separated FOG (c) internally dispose retained FOG by means and methods of mass and volume reduction as required by para. 4.3.2 The use ofalternate materials or methods are permitted, provided the proposed material and method complies with the performance requirements and intent of this Standard. 1.2 Units of Measurement Where values are stated in U.S. Customary units and the International System of Units (SI), the U.S. Customary units shall be considered as the standard. In this Standard, gallons (U.S. liquid) per minute is abbreviated “gpm” and liters (metric liquid) per minute is abbreviated “L/min”. 1.3 References The following is a list of publications referenced in this Standard: AASHTO H20‐44, Standard Specifications for HS‐20, Highway Loading Publisher: American Association ofState Highway and Transportation Officials (AASHTO), 444 North Capitol Street, NW, Washington, DC 20001 (http://www.transportation.org) ACI 318, Specification for Steel Reinforcement Publisher: American Concrete Institute (ACI), 38800 Country Club Drive, Farmington Hills, MI 48331 (http://www.aci-int.org) ASME A112.3.1, Stainless Steel Drainage Systems for Sanitary, Storm, and Chemical Applications, Above and In‐Ground ASME A112.14.3, Grease Interceptors ASME B1.20.1, Pipe Threads, General Purpose (Inch) Publisher: The American Society ofMechanical Engineers (ASME), Three Park Avenue, New York, NY 10016-5990; Order Department: 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900 (http://www.asme.org)
ASTM A 888, Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications ASTM C 33‐03, Standard Specification for Concrete ASTM C 94, Standard Specification for Ready‐Mixed Concrete ASTM C 150‐04, Standard Specification for Portland Cement ASTM C 260‐01, Standard Specification for Air‐Entraining Admixtures for Concrete ASTM C 618‐03, Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete Publisher: American Society for Testing and Materials (ASTM International), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 (http://www.astm.org) IAPMO/ANSI Z 1001, Grease Interceptors Publisher: International Association of Plumbing and Mechanical Officials (IAPMO), 5001 East Philadelphia Street, NW, Ontario, CA 91761 (http://www.iapmo.org) PDI‐G101, Testing and Rating Procedure for Grease Interceptors With Appendix of Sizing and Installation Data Publisher: Plumbing and Drainage Institute (PDI), 800 Turnpike Street, North Andover, MA 01845 (http://www.pdionline.org) UL 499, Electrical Standard for Heated Appliances UL 917, Standard for Clock‐Operated Switches UL 1004, Standard for Electric Motors UL 1585, Standard for Class 2 and Class 3 Transformers Publisher: Underwriters Laboratories, Inc. (UL), 333 Pfingsten Road, Northbrook, IL 60062-2096 (http://www.ul.com) USEPA Method 1664 (A), FOG (Fats, Oils & Greases) Measurement
2 GENERAL REQUIREMENTS 2.1 Construction FOG disposal systems shall be manufactured from materials such as, but not limited to, concrete, steel, stainless steel, fiberglass, reinforced polyester, polyethylene, and polypropylene. Such materials shall be rated and suitable for the intended application. 2.1.1 Design Performance. FOG disposal system designs and methods shall produce an effluent quality not to exceed 100 mg/L FOG as stated in para. 4.3.2. 2.1.2 Flow Rate. FOG disposal systems shall be described by total gpm influent. 2.1.3 Inlet and Outlet Connections. The inlet and outlet connections ofthe FOG disposal system shall be either a female pipe thread or a plain end diameter to allow hubless coupling connections. Tapered threads shall comply with ASME B1.20.1. Hubless connections shall comply with the outside dimension for the given pipe size in accordance with ASTM A 888 or ASME A112.3.1. 2.2 Electrical All electrical components used in the FOG disposal system shall conform to the appropriate sections of UL Standards 499, 917, 1004, and 1585 as listed in para. 1.3. 2.3 Manufacture 2.3.1 FOG disposal systems shall be free of manufacture and/or material defects that affect performance, or serviceability. 2.3.2 FOG disposal systems shall be designed to withstand anticipated installation and use associated FOG loading. 2.3.3 Each FOG disposal system and cover designated for buried application shall be structurally designed to withstand earth or other loads pertinent to its location.

Related PowerPoint Templates

Template Categories
Popular Tags