Home>ASME standards>ASME A112.19.2-2008 pdf download

ASME A112.19.2-2008 pdf download

ASME A112.19.2-2008 pdf download.Ceramic plumbing fixtures.
2 Reference publications This Standard refers to the following publications, and where such reference is made, it shall be to the edition listed below, including all amendments published thereto. CSA (Canadian Standards Association) CAN/CSA-B1 25.3-05 Plumbing fittings CAN/CSA-B651 -04 Accessible design for the built environment CAN/CSA-B1 800-06, Thermoplastic nonpressure piping compendium CAN/CSA-B1 81 .1 -06 Acrylonitrile-butadiene-styrene (ABS) drain, waste, and vent pipe and pipe fittings CAN/CSA-B1 81 .2-06 Polyvinylchloride (PVC) and chlorinated polyvinylchloride (CPVC) drain, waste, and vent pipe and pipe fittings C22.2 No. 0.1 5-01 (R2006) Adhesive labels ASME (American Society of Mechanical Engineers) A1 1 2.6.1 M-1 997 Floor Affixed Supports for Off-the-Floor Plumbing Fixtures for Public Use A1 1 2.6.2-2001 Framing-Affixed Supports for Off-the-Floor Water Closets with Concealed Tanks A1 1 2.1 9.5-2005 Trim for Water-Closet Bowls, Tanks, and Urinals Ceramic plumbing fixtures August 2008 3 © American Society of Mechanical Engineers © Canadian Standards Association A1 1 2.1 9.1 2-2006 Wall Mounted, Pedestal Mounted, Adjustable, Elevating, Tilting, and Pivoting Lavatory, Sink and Shampoo Bowl Carrier Systems and Drain Waste Systems A1 1 2.1 9.1 4-2006 Six-Liter Water Closets Equipped with a Dual Flushing Device A1 1 2.1 9.1 9-2006 Vitreous China Nonwater Urinals ASME/CSA (American Society of Mechanical Engineers/Canadian Standards Association) ASME A1 1 2.1 8.1 -2005/CAN/CSA-B1 25.1 -05 Plumbing supply fittings ASME A1 1 2.1 8.2-2005/CAN/CSA-B1 25.2-05 Plumbing waste fittings ASSE (American Society of Sanitary Engineering) 1 002-1 999 Performance Requirements for Anti-Siphon Fill Valves (Ballcocks) for Gravity Water Closet Flush Tanks 1 037-1 986 Performance Requirements for Pressurized Flushing Devices for Plumbing Fixtures ASTM International (American Society for Testing and Materials) D 331 1 -06a Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns IAPMO/ANSI (International Association of Plumbing and Mechanical Officials/American National Standards Institute) Z1 24.4-2006 Plastic Water Closet Bowls and Tanks ICC/ANSI (International Code Council/American National Standards Institute) A1 1 7.1 -2003 Accessible and Usable Buildings and Facilities UL (Underwriters Laboratories Inc.) 969 (1 995) Standard for Marking and Labeling Systems 3 Definitions and abbreviations 3.1 Definitions The following definitions apply in this Standard: Air gap — the unobstructed vertical distance, through the open atmosphere, between the lowest opening of a water supply and the flood level of the fixture. Anti-siphon fill valve — a valve that is used to supply water to a flush tank and has, on its discharge side, an air gap, integral mechanical backflow preventer, or vacuum breaker. It is operated by a float or similar device. 4 August 2008 © American Society of Mechanical Engineers ASME A112.19.2-2008/CSA B45.1-08 © Canadian Standards Association Bidet — a fixture with a hot and cold water supply intended for genital and perineal hygiene. Blowout action — a means of flushing a water closet whereby a jet of water directed at the bowl outlet opening pushes the bowl contents into the upleg, over the weir, and into the gravity drainage system. Blowout bowl — a non-siphonic water closet bowl with an integral flushing rim, a trap at the rear of the bowl, and a visible or concealed jet that operates with a blowout action. China — Non-vitreous china — ceramic material in which porosity results in a water absorption of between 0.5 and 1 5.0% of the original weight of the dry specimen (see Clause 6.1 ). Vitreous china — ceramic material fired at a high temperature to form a non-porous body with a maximum water absorption of 0.5% of the original weight of the dry specimen (see Clause 6.1 ). Critical level (CL) — the highest water level of a fixture at which back siphonage will not occur. Defect — Blister (large) — a hollow raised portion of the glazed surface of a fixture with a dimension greater than 3 mm (0.1 3 in). Bubble — a raised portion of the glazed surface of a fixture or a sand speck whose largest dimension is less than 1 mm (0.04 in). Crack — a fracture in the glaze or the body of a fixture, but not a dunt or a craze. Craze (crazing) — fine cracks in the surface finish. Discoloration — a coloured spot with a dimension greater than 6 mm (0.25 in) or specks or spots in sufficient number that a change in colour is produced. Dull or eggshell finish — a dead, flat, slightly matted, undeveloped glaze or semi-glazed finish with numerous very fine pinholes. Note: Dull or eggshell finish is not to be confused with a satin or matte finish used for decorative purposes. Dunt — a hairline fracture extending through the body of a fixture and caused by strains during manufacturing. Exposed body — an unglazed portion of a fixture with a dimension of 2 mm (0.08 in) or greater. Fire check — a fine shallow crack in the body of a fixture that is not covered with glaze. Pinhole — a hole in the glazed surface of a fixture whose largest dimension is 2 mm (0.08 in) or less. Pit — a hole in the glazed surface of a fixture with a dimension greater than 2 mm (0.08 in). Speck — an area of contrasting colour whose largest dimension is between 0.3 and 1 mm (0.01 and 0.04 in). Spot — an area of contrasting colour whose largest dimension is greater than 1 mm (0.04 in) but less than 3 mm (0.1 3 in). Wavy finish — a defect in a finish that results in numerous irregular or mottled runs in the glaze. Fill time — the time from the instant the flush valve of a water closet tank closes until the instant the fill valve is completely shut off. Finish — the texture and condition of a surface (excluding colour).

Related PowerPoint Templates

Template Categories
Popular Tags