Home>ASME standards>ASME A112.6.7-2010 pdf download

ASME A112.6.7-2010 pdf download

ASME A112.6.7-2010 pdf download.Sanitary Floor Sinks.
1 GENERAL 1.1 Scope This Standard applies to sanitary floor sinks and includes requirements for material, construction, inspec- tion, testing, and marking. The provisions of this Standard are not intended to prevent the use of any alternate materials or methods ofconstruction, provided any such alternate meets the intent of this Standard. 1.2 Units of Measurement Values are stated in U.S. Customary units and the International System of Units (SI). The U.S. Customary units shall be considered as the standard. 1.3 References The following documents form a part of this Standard to the extent specified herein. Unless otherwise speci- fied, the latest edition shall apply. ASME A112.6.3-2001, Floor and Trench Drains ASME A112.18.1/CSA B125.1-05, Plumbing Fixture Fittings ASME A112.18.2/CSA B125.2-05, Plumbing Fixture Waste Fittings ASME A112.19.1/CSA B45.2-08, Enameled Cast Iron and Enameled Steel Plumbing Fixtures ASME A112.19.3/CSA B45.4-08, Stainless Steel Plumbing Fixtures Publisher: The American Society of Mechanical Engineers (ASME), Three Park Avenue, New York, NY 10016-5990; Order Department: 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900 (www.asme.org) ASTM A 888, Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications ASTM D 522, Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings ASTM D 523, Standard Test Method for Specular Gloss ASTM D 1784, Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds ASTM D 2665, Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
2 GENERAL REQUIREMENTS 2.1 Materials 2.1.1 Enameled and Epoxy-Coated Cast Iron Floor Sink. The enameled and epoxy-coated cast iron floor sink shall conform to the general requirements outlined in ASME A112.19.1/CSA B45.2-08, Section 4, and surface shall be examined for blemishes in accordance with para. 5.2. 2.1.2 PVC Plastic Floor Sinks. PVC floor sinks shall be made of a single PVC virgin compound except as provided in para. 2.1.2.1, and shall conform to the requirements specified in ASTM D 1784 for a PVC 12454 compound. The PVC plastic floor sinks shall conform to the general requirements outlined in IAPMO/ ANSI Z124.6-2007, Section 2 and workmanship and fin- ish in Section 3. 2.1.2.1 Reworked Plastic. Clean, reworked plastic generated from the manufacturer’s own PVC 12454 products may be used provided the floor sinks produced meet the requirements of this Standard. 2.1.3 Stainless Steel FloorSinks. The stainless floor sink shall conform to the general requirements outlined in ASME A112.19.3/CSA B45.4-08, Section 4, and surface shall be examined for blemishes in accordance with para. 5.1. 2.2 Epoxy Coating The visible surface after installation of each floor sink shall be acid-resisting epoxy, thoroughly fused to the cast iron base. It shall be free from flaws that may affect the appearance or serviceability of the floor sink. The epoxy surface shall meet the requirements of ASME A112.19.1/CSA B45.2-08, para. 4.1.2 when evalu- ated for surface defects in accordance with para. 5.2.
2.2.2 Epoxy Thickness. The thickness of the epoxy coating, as measured on a flat surface at least 1 in. (25 mm) from any edge shall be not less than 4 mils (0.1 mm). 2.2.3 Acid Resistance. The epoxy coating shall be acid resisting when tested in accordance with para. 5.3. 2.2.4 Epoxy Flexibility. The epoxy shall be flexible when tested in accordance with para. 5.4. 2.3 Detail Requirements 2.3.1 Floor Sink Drain Body. The drain body shall be smooth with rounded corners to eliminate bacterial catching surfaces. Drains and other waste-fitting compo- nents shall comply with ASME A112.18.2/ CSA B125.2-05. 2.3.2 Strainers and Grates. The strainers and grates shall be accessible and removable for cleaning and main- tenance. The grates must be aligned properly and fas- tened by accompanying screws, unless floor sink design is for loose set installation. 2.3.3 Open Area. The grates and strainers shall com- ply with the open area requirements of ASME A112.6.3-2001. 2.3.4 Screws. All screws shall be made ofcorrosion- resistant material. 2.3.5 Dimensions. PVC floor sink dimensions shall conform to the socketand spigotdimensions as specified in ASTM D 2665.

Related PowerPoint Templates

Template Categories
Popular Tags