ASME AG-1a-2005 pdf download

ASME AG-1a-2005 pdf download.CODE ON NUCLEAR AIR AND GAS TREATMENT.
The requirements of Article AA-6000 shall apply except where expanded upon, modified, or otherwise exempted by the following. RA-6100 WELDING AND BRAZING RA-6110 WELDING AND BRAZING PERFORMED ON ASME CODE, SECTION III, PRESSURE- RETAINING COMPONENTS AND SUPPORTS Welding and brazing performed on ASME Code, Section III, pressure-retaining components and Section III, Subsection NF, component supports shall be in accordance with Code Sections III and IX. RA-6120 WELDING AND BRAZING PERFORMED ON ASME CODE, SECTION VIII, PRESSURE- RETAINING COMPONENTS Welding and brazing performed on Section VIII pressure-retaining components shall be in accordance with Code Sections VIII and IX. RA-6130 WELDING AND BRAZING OF NON-ASME BOILER AND PRESSURE VESSEL CODE PRESSURE RETAINING COMPONENTS AND SUPPORTS RA-6131 General RA-6131.1 Scope. The requirements of this para- graph apply to the preparation of welding and brazing procedure specifications, the qualification of welding and brazing procedures, welders, brazers, and welding operators for all types of manual and machine welding 245 and brazing processes, and the workmanship, weld quality, brazing quality, and inspection of weldments and brazed joints produced during the manufacture of refrigeration equipment and components. RA-6131.2 Responsibility. Each Manufacturer is responsible for the welding and brazing done by his organization and shall conduct the tests required by this subparagraph to qualify the procedures used in the construction of the weldments and brazed joints built under this Code, the performance of brazers, welders, and welding operators who apply these procedures, and the inspections required for workmanship and quality verification. RA-6131.3 Base Metal. Base metals to be joined by welding or brazing shall be one of those listed in Article RA-3000 or a combination of the base metals listed in Article RA-3000, provided the requirements of RA-6131.2 are met. RA-6132 Welding Procedures Qualification of the Manufacturer’s welding proce- dure specifications shall be in accordance with the requirements of this section and either the ASME Code, Section IX, or ANSI/AWS D1.1. Once a choice is made between Section IX or ANSI/AWS D1.1, all qualifications shall be consistent with that particular document. RA-6133 Welder and Welding Operator Qualifications RA-6133.1 Welder or welding operator qualification testing, or both, shall be performed in accordance with the ASME Code, Section IX, or ANSI/AWS D1.1. Welding of the qualification test specimens shall be performed in accordance with the Manufacturer’s weld- ing procedure specification qualified in accordance with RA-6132.
RA-7100 GENERAL REQUIREMENTS (a) Packaging, shipping, receiving, storage, and han- dling requirements shall be in accordance with AA- 7000, ASME NQA-1 Requirement 13, ASME NQA- 1, Subpart 2.2, and the specific requirements of this Article. (b) When different levels ofclassification are required for different parts of the machine, the Manufacturer’s procedures shall state how this will be addressed. If the Owner has specific requirements, the design specification shall so state. RA-7200 PACKAGING All relevant equipment listed in ASME NQA-1, Subpart 2.2, paras. 302.2 and 302.3, shall meet the requirements of Packaging Levels B or C, as applicable, of ASME NQA-1, Subpart 2.2, para. 300. The balance of the machine shall meet the requirements of Packaging Level D of ASME NQA-1, Subpart 2.2, para. 300. RA-7300 SHIPPING All relevant equipment listed in ASME NQA-1, Subpart 2.2, paras. 302.2 and 302.3, shall meet the requirements of Shipping Levels B or C, as applicable, of ASME NQA-1, Subpart 2.2, para. 400. The balance of the machine shall meet the requirements of Shipping Level D of ASME NQA-1, Subpart 2.2, para. 400. RA-7400 STORAGE All relevant equipment listed in ASME NQA-1, Subpart 2.2, paras. 302.2 and 302.3, shall meet the requirements of Storage Levels B or C, as applicable, of ASME NQA-1, Subpart 2.2, para. 600. The balance of the machine shall meet the requirements of Storage Level D of ASME NQA-1, Subpart 2.2, para. 600. 247 RA-7500 HANDLING AND RIGGING Handling and rigging requirements shall be in accord- ance with AA-6610 and the following. All relevent equipment listed in ASME NQA-1, Subpart 2.2, paras. 302.2 and 302.3, shall meet the requirements of Handling Levels B or C, as applicable, of ASME NQA-1, Subpart 2.2, para. 700. The balance of the machine shall meet the requirements of Handling Level D of ASME NQA-1, Subpart 2.2, para. 700. RA-7600 ASSEMBLY, ERECTION, AND START-UP RA-7610 FIELD-ASSEMBLED OR FIELD- ERECTED EQUIPMENT Where equipment requires component assembly dur- ing final installation, the equipment manufacturer shall provide detailed written procedures for making the proper final assembly in accordance with AA-6620. RA-7620 EXTERNAL CONNECTIONS AND SERVICES (a) All external connections and services essential to the proper and safe operation of the refrigeration equipment supplied by the Owner or his designee shall be, as a minimum, governed by the same criteria as those specified as applicable to the refrigeration equipment itself.