ASME Y14.34-2008 pdf download
ASME Y14.34-2008 pdf download.Associated Lists.
5.1 Integral Parts List Format When an integral parts list is prepared as a separate sheet or sheets of the drawing, the size of the sheets should be the same size as the other sheets of the draw- ing. The PL prefix shall not be used with integral parts lists. 5.1.1 When an integral parts list is included on a drawing sheet or sheets that denote the graphic presen- tation, the heading shall be PARTS LIST, as shown in Fig. 2 or 3. 5.1.2 When an integral parts list is included as digital data files or manually prepared separate drawing sheets, the heading shall be PARTS LIST, as shown in Fig. 3. 5.1.3 Each sheet of an integral parts list shall be numbered as a sheet(s) of the drawing. 5.1.4 An integral parts listshall be located in accor- dance with Figs. 2 and 3. 5.2 Separate Parts List Format 5.2.1 Heading Requirements. For heading require- ments, see para. 4.6. 5.2.2 Cross-Reference 5.2.2.1 When a separate parts list is used, the engineering drawing with which the parts list is associ- ated shall contain a cross-reference note, e.g., “SEE SEPARATE PARTS LIST.” For manually prepared draw- ings, the cross-reference note shall be located above the title block. For electronically prepared drawings, the cross-reference note shall be located in the general notes (see ASME Y14.41). 5.2.2.2 When drawing data, e.g., notes, applica- tion data, and wire data, are provided on a separate parts list, a note with content and location similar to that required by para. 5.2.2.1 shall be used. 5.3 Integral and Separate Columnar Entries 5.3.1 The column entries shall include the manda- tory information shown in Fig. 4. Other information may also be included. Other types of notes may be added or referenced in the NOTES OR REMARKS column. 5.3.2 Optional columns may be included, but need not be limited to, listing the following entries: (a) UnitofMeasure. Units ofmeasure otherthanquan- tity may be entered in this column, or in the quantity column per Fig. 4.
(b) Drawing or Document Number. The following information may be entered: (1) the documentnumber applicable to the material fromwhicha listed partdelineatedonthe corresponding drawing is fabricated (2) the documentnumberapplicable to a listed item for which a designation type, class, condition, or other information has been entered in the part or identifying number column (3) the drawing number applicable to a listed item in the part or identifying number column (4) the document number when the part is defined by a number that must be decoded by using the procure- ment specification (5) referenced documents (c) Size. A SIZE column may be included to indicate the document size. (d) Materials. A MATERIALS column may be included to specify material used in the fabrication of items detailed on the related drawing. An included materials column may also be used to delineate materi- als used in subordinate details, assemblies, and items identified on control or modifying drawings. 6 APPLICATION LIST PREPARATION 6.1 Integral Application List When application data is provided integral to the drawing but separate from an integral parts list, the data shall be presented in an application block per ASME Y14.1 or ASME Y14.1M. 6.2 Separate Application List 6.2.1 Heading Requirements. For heading require- ments, see para. 4.6. 6.2.2 Column Entries. The column entries in Fig. 5 shall apply, as a minimum, in preparation of a separate application list. 7 DATA LIST PREPARATION 7.1 Heading Requirements For heading requirements, see para. 4.6. 7.2 Content Data list entries shall be segregated into the following order of groups: (a) drawings (b) lists — as specified herein, and other lists (usage, inspection, equipment, or other) (c) specifications (d) standards (e) publications (f) otherdocuments referencedondrawings andasso- ciated lists
